Skip to main content

Day Chapel

Need Help? Call Tech! 678-405-2289 If you need assistance with Perimeter Audio, video or lighting systems.

For reporting Non-Emergency Gear or Room Problems, email us at techhelp@perimeter.org

**NOTE: If you Utilize the Chapel iPads, they MUST be returned to the storage location behind the stage, and plugged in to charge, so they are ready to go for the next event.

How to Use the Belt Pack and Headset Microphone​

The belt pack is a versatile piece of equipment that allows you to use a headset microphone for enhanced audio quality. This guide will walk you through the steps to properly set up and use the belt pack and headset microphone.

Accessing the Belt Pack​

  • Locate the designated drawer where the belt pack is stored and open it.

Battery Installation​

  • Take out the rechargeable batteries stored in the same drawer.
  • Insert the battery into the belt pack, ensuring that the text on the battery is readable. This confirms that the battery is placed correctly.
  • Close the battery compartment.

Powering On​

  • Turn on the belt pack using the switch located at the top.
  • For the next steps, make sure to turn off the belt pack.

Steps to Attach the Headset​

Locating the Headset​

  • The headset is stored in a small case near the belt pack drawer.
  • Open the case and take out the headset.

Connecting the Headset​

  • Locate the end of the headset that screws into the belt pack.
  • Align the two small knobs on the back of the headset connector with the corresponding slots on the belt pack.
  • Once aligned, the connector will click into place, allowing you to screw it in securely.

Final Steps​

  • Turn the belt pack back on.
  • Place the headset over your ear to complete the setup.

How to Properly Store the Belt Pack and Headset After Use​

Steps for Storing the Headset​

Disconnecting the Headset​

  • Unscrew the headset from the belt pack and remove it.

Wrapping Up the Headset​

  • If there are any knots, untangle them first.
  • Neatly wrap the headset cable.

Storing the Headset​

  • Place the wrapped headset back into its designated case.
  • Thread the small loop on the case through the headset cable for added security.
  • Zip up the case.

Steps for Storing the Belt Pack​

Powering Off​

  • Make sure the belt pack is turned off.

Removing the Battery​

  • Open the battery compartment and remove the battery.

Charging the Battery​

  • Place the battery back in its charger, ensuring that the circle and tab on the battery are facing outward.
  • Press down on the battery to secure it in the charger.

Storing the Belt Pack​

  • Place the belt pack back in its designated spot in the drawer.

How to Record Room Audio Using the Denon System​

Initiating the Recording​

  • Locate the Denon system and identify the "Record" button.
  • Press the "Record" button once; it will start blinking to indicate it's ready.
  • Press the "Record" button again to start the recording. The light will turn solid red, confirming that the recording has begun.

Monitoring the Recording​

  • Keep an eye on the Denon system's display. It will show a timer, indicating the duration of the recording.

Stopping the Recording​

  • To stop the recording, simply press the "Stop" button on the Denon system.

Saving and Scheduling​

  • The recording will automatically be saved on the server.
  • For recurring meetings, they are usually pre-scheduled to be recorded. However, it's always good practice to double-check if you want your specific meeting to be recorded.

Handheld Microphone Operation Guide​

Battery Installation​

  1. Locate the Microphone: Find the handheld microphone stored in the designated area.
  2. Open the Battery Compartment: Unscrew the bottom part of the microphone to access the battery compartment.
  3. Remove Old Battery: If there's an old battery, remove it. The batteries are rechargeable and stored in a specific area.
  4. Insert New Battery:
  • Positive end should be on top.
  • Negative end should be on the bottom.
  1. Close the Compartment: Screw the bottom part back on.

Turning On and Off​

  • To Turn On: Slide the switch to the right.
  • To Turn Off: Slide the switch back to its original position.

Battery Removal and Storage​

  1. Open the Compartment: Unscrew and open the battery compartment.
  2. Remove the Battery: Take out the battery.
  3. Proper Orientation: When placing the microphone back, ensure the side with the circle and tab is facing the correct way.
  4. Close and Store: Close the compartment and store the microphone in its designated area.